Radix epsilon Manual de instrucciones

Instruction ManualRADIX Electronic Vertriebs-GmbH • D-61381 Friedrichsdorf • F.R. GermanyRead this instruction manual through carefully first. • Keep

Installing the ReceiverPage 10 Version 1.05 Installing the Receiver5.1 Prerequisites and Ambient ConditionsNOTE:Keep the receiver well away from sou

Installing the ReceiverVersion 1.0 Page 115.2.1 Single-Antenna Operation5.2.2 Dual-Antennae OperationGBAC95~265V50Hz MAX30WRF INPUT+13V/+18V400mA MAX.

Programming and Operating the Analog-Receiver SectionPage 12 Version 1.06 Programming and Operating the Analog-Receiver Section• Switch the receiver

Programming and Operating the Analog-Receiver SectionVersion 1.0 Page 136.2 Preselecting Channels from the Main Menu (Display Page 1)• Press the MEN

Programming and Operating the Analog-Receiver SectionPage 14 Version 1.06.3 Preselecting Channels from the Main Menu (Display Page 2)• Press the q

Programming and Operating the Analog-Receiver SectionVersion 1.0 Page 156.4 Preselecting Channels from the Main Menu (Display Page 3)The settings of

Setting Up and Programming the Digital ReceiverPage 16 Version 1.07 Setting Up and Programming the Digital Receiver7.1 Switching On the Receiver•

Setting Up and Programming the Digital ReceiverVersion 1.0 Page 177.2 Language Selection• Use the p and q keys to highlight the “Language”field, as s

Setting Up and Programming the Digital ReceiverPage 18 Version 1.07.4 Setting Decoder StatusSelecting the TV Aspect Ratio:• Use the p and q keys to

Setting Up and Programming the Digital ReceiverVersion 1.0 Page 19• Press the MENU-key.• Use the p and q keys to highlight the “OLD” DiSEqC-setting.

IntroductionPage 2 Version 1.01 IntroductionCongratulations on your decision to purchase a RADIX digital satellite receiver. All of ourmanufacturing

Setting Up and Programming the Digital ReceiverPage 20 Version 1.0The displayed data concerns the revision of the decoder firmware current at thetime

Setting Up and Programming the Digital ReceiverVersion 1.0 Page 217.5.2 Adjusting the DiSEqC-Controller and/or the 22-kHz Control SignalNOTE:This adj

Setting Up and Programming the Digital ReceiverPage 22 Version 1.07.5.3 Entering the Low-Noise Block (LNB) Converter’s Local-Oscillator FrequencyCom

Setting Up and Programming the Digital ReceiverVersion 1.0 Page 23• Cautiously realign the antenna until the triangular figure reachesmaximum size.Yo

Setting Up and Programming the Digital ReceiverPage 24 Version 1.07.6 Manual Channel Preselection7.6.1 Entering the Downlink FrequencyOnce the setti

Setting Up and Programming the Digital ReceiverVersion 1.0 Page 257.6.2 Entering the Symbol Rate• Use the p and q keys to highlight the “Symbol Rate

Setting Up and Programming the Digital ReceiverPage 26 Version 1.07.6.4 Conducting a Manual SearchOnce the settings of Sections 7.6.1 through 7.6.3,

Operating the Digital ReceiverVersion 1.0 Page 278 Operating the Digital ReceiverOnce all of the above settings have been made, your receiver will be

Operating the Digital ReceiverPage 28 Version 1.08.3 Using Channel DirectoriesDue to the large number of digital television channels, channel direct

Operating the Digital ReceiverVersion 1.0 Page 29Moving Channels:• Use the t and u to highlight the “Move” field.• Press the MENU-key to confirm you

ContentsVersion 1.0 Page 32 ContentsSection Title Page1 Introduction 22 Contents 33 Safety Precautions 54 The Receiver and Its Operation 64.1 The Remo

Operating the Digital ReceiverPage 30 Version 1.0• Use the p and q keys to highlight the channel to be deleted.• Press the MENU-key. The channel i

Operating the Digital ReceiverVersion 1.0 Page 318.4 Adjusting the Volume of the Sound Track/Muting• Press the MUTE-key to mute the sound track.• E

Operating the Digital ReceiverPage 32 Version 1.0• Use p and q keys to select the language desired.• Press one of the t or u keys to highlight the

Operating the Digital ReceiverVersion 1.0 Page 33This information largely consists of programming schedules, along with additionalinformation provided

Programming the Remote ControlPage 34 Version 1.09 Programming the Remote ControlThe remote control may be programmed using two different methods, e

Troubleshooting TipsVersion 1.0 Page 35Step 4: Press the SET-key to save the setting. The red LED willblink three times and then be extinguished.If n

ContentsPage 4 Version 1.08 Operating the Digital Receiver 278.1 Switching On the Receiver 278.2 Channel Selection 278.3 Using Channel Directories 28

Safety PrecautionsVersion 1.0 Page 53 Safety PrecautionsThis receiver is intended exclusively for the reception of satellite broadcasts, and should be

The Receiver and Its OperationPage 6 Version 1.04 The Receiver and Its Operation4.1 The Remote ControlNumerical KeysCursor-Control Key (cursor up)C

The Receiver and Its OperationVersion 1.0 Page 7Key Function During:Marking(s) Color Operation

The Receiver and Its OperationPage 8 Version 1.0Key Function During:Marking(s) Color Operation

The Receiver and Its OperationVersion 1.0 Page 94.2 The Receiver UnitControls and displays on the receiver’s front panelConnectors on the receiver’s